How to Find Purlins and Girts on Building Drawings

Start with the member's location. Roof supports belong on the roof framing pages. Wall supports belong on the wall framing pages. Once you find that view, follow the piece's mark to the parts list and connection detail.
A purlin supports roof panels. A girt supports wall panels. An eave strut sits at the eave, where the low roof edge meets the wall. These names help you find the right page. They are not complete ordering descriptions.
You do not need to understand every line in the drawing set. Work from the building location to one marked piece.
Put the building and the pages in the same direction
Bring the full drawing set, a notebook, a pencil, and a phone. Use paper copies or save the files where you can reopen them. A cropped screenshot often leaves out the page title and reference marks.
Walk around the building from the ground. Pick a fixed landmark, such as the large door or a distinct corner. Sketch it on your notebook page. Note which wall contains the member you want to identify.
A plan is a view from above. An elevation is a view looking at a wall. A section is a cut-through view that shows how parts meet. Keep those meanings beside your sketch until the terms become familiar.
Look for the title block on each sheet. This is the information box containing the sheet name and number. Read those names before searching individual lines. A roof panel layout and a roof framing plan answer different questions.
Follow one member through the drawing set
- Open the layout for its location. Use the roof framing plan for purlins. Use the matching wall framing elevation for girts.
- Find your landmark. Compare the door, corner, or wall label with your ground sketch. Make sure you are looking at the correct wall.
- Locate the space between main frames. This space is called a bay. Use the drawing's grid labels to identify it. Grid labels are the letters or numbers marking frame lines.
- Read the member mark. Copy the code printed beside the member. Include every letter and number. Do not replace it with a general name.
- Search the parts list for that mark. Record the section designation, quantity, and listed length. Keep the code attached to those fields.
- Follow its detail reference. A detail is an enlarged drawing of a small area, often a connection. Copy both the detail label and the sheet where it appears.
- Compare with what is visible. Photograph the actual mark if you can reach it safely from the floor. Note anything that disagrees with the drawing.
Do not tighten bolts or move a member while tracing its identity. Finding a mark is a reading task. Changing a connection is a separate job.
Fill in a drawing-navigation worksheet
Use this worksheet for the single piece you are investigating. It keeps the building view, list entry, and detail together.
| Worksheet field | Your entry |
|---|---|
| Ground landmark | Door, corner, or other fixed feature |
| Building face | Your plain-language wall or roof description |
| Layout page | Sheet name and sheet number |
| Grid or bay | Labels copied exactly from that page |
| Member role | Purlin, girt, eave strut, or uncertain |
| Member mark | Complete code, including suffix |
| Parts-list entry | Page and matching row |
| Section drawing | Page showing the member's end shape |
| Connection detail | Detail label and sheet number |
| Physical comparison | Matching mark, unreadable mark, or difference |
| Remaining question | The specific missing page or information |
Finish by writing one sentence: “The piece beside this landmark is marked this way on this sheet.” Attach the landmark photo. Someone else should be able to find the same piece without walking around with you.
Read the detail without treating it as a shopping sketch
A section drawing helps identify the shape. A connection detail shows how that member meets other parts. Check that both belong to the mark and location you found.
The building's drawings decide spans, member sizes, bolt patterns, overlaps, and loads. Do not copy those requirements from a sample manual for another building. If a connection requirement is missing, ask the building maker or an engineer to resolve it.
For panels and their fasteners, the building's drawings or panel maker's installation instructions decide the fastening pattern and support requirements. A framing illustration on a product page does not replace either source.
If you see two different marks at the same location, write down both. Include the page names. Ask which piece belongs there before treating one as a corrected version.
Start from the building when the paperwork is missing
Look through stored paperwork for the original building name, order number, and parts list. Search digital folders for scans too. The building maker may be able to locate its original drawing set from those records.
Without drawings, photograph the wall or roof from a safe place. Identify the fixed landmark, visible member ends, and readable labels. Mark hidden areas as hidden. Do not remove wall panels simply to complete the worksheet.
Use C vs Z Purlins: How to Tell Them Apart to identify a visible end shape. If the job involves damaged framing, continue with How to Identify a Replacement Metal Building Girt. An engineer can assess the building when the original requirements cannot be recovered.
Take only confirmed information to the product comparison
The catalog lists 8-inch Cee purlin, 8-inch Zee purlin, and Eave strut. Use those pages after identifying the required member. Compare complete section information and holes before choosing a candidate.
Do not call every wall support a purlin. Do not select an eave member just because it is nearest the roof. Most of all, do not lose the member mark when copying dimensions into a separate list.
Your useful result is a traceable route through the pages. It should connect a real building location to a specific piece and its detail. Anything still uncertain belongs in the last worksheet row, where it can be answered before the parts order grows.